How To Install A Cork Wall
Easy, step-by-footstep instructions for installing corkboard walls perfect for an office or kids' room. This uncomplicated cork wall DIY projection is cheap and can easily be removed when no longer wanted or needed!
Welcome back to our third week in the $100 Room Claiming!
I'grand so excited to be participating in this flavour along with our host, Erin from Lemons, Lavander & Laundry, and many other fabulous bloggers.
If yous're just joining united states, you can catch upwardly on my son's room makeover (in merely one month and for less than $100) in the post-obit posts:
WEEK one – THE BEFORE | Calendar week 2 – DIY LEGO TABLE
I'm posting every Wednesday in January with the large reveal on the 29th!
Allow's begin by looking at our mini-project list progress:
-
Paint the green wall -
Remove the loft bed - Build and install a new bed
- Organize the cupboard (which includes
sorting through his dressand all their books) - Sort through and purge the non-LEGO toys and blimp animals
-
Install the cork wall - Organize the LEGOs
- Final decorating!
I know last week I mentioned we'd be edifice Andrew's bed over the by weekend, but our unabridged family unit got sick so plans had to change…
Instead, we've installed his super cool cork panel wall!
I as well spent some fourth dimension going through his clothes and donating anything he'd outgrown. And then #four is halfway in that location. 😉
Here's a await at the room every bit of now:
The bed volition stay where the mattress is sitting and I'm still not sure exactly how the cubby shelves and LEGO tabular array will arrange when all is said and done…
Every bit Chris would tell you, I tend to make up one's mind those things on the reveal photograph shoot day. 😉
You can run into the cork wall tucked backside his door on the left of this moving picture:
So far we've spent a total of $85 ($36 on lumber for the bed and $49 on the cork wall) out of our $100 budget.
The cork wall could have been cheaper if we were willing to adhere the cork directly to the drywall, just we wanted it to exist easily removable in the hereafter and then we spent a little actress to build it on plywood.
Speaking of the cork wall, I'one thousand super excited to share with you all the details for how to make a cork lath wall then allow'southward get to it, shall we?
RELATED: HOW TO Gear up AN EFFICIENT PRINTER STATION
DIY Cork Wall
For a printable copy of the materials and instructions, roll downwardly.
Materials Needed:
- Cork Rolls
- Spray Agglutinative
- 1/4″ Plywood
- Screws
- Finish Washers
Tools Needed:
- Jig Saw
- J-Roller
- Box Pocketknife
- Drill
How to Make a Cork Lath Wall
Pace 1: Cutting your plywood.
Brainstorm by measuring the wall you desire to turn into a corkboard wall and so use a jig saw to cutting your plywood to fit exactly on the wall.
Our wall was about a 4'x8′ surface area (aforementioned size as a typical sheet of plywood) and so Chris only had to trim a bit off the bottom and a notch for our door trim.
If your wall is larger than ane sheet of plywood, grab every bit many pieces every bit y'all need.
Many home improvement stores also sell smaller "craft" size pieces of plywood so you could utilise this to make 1 that'due south more similar two'x4′ if that'due south what y'all desire.
Once the plywood is cut to size, test fit it to make sure information technology'due south skillful to go.
Here's how ours looked when we test-fit it:
If needed, make small adjustments using sandpaper or your jig saw until information technology fits nicely.
STEP 2: Glue on the cork board.
Adjacent you're going to glue the cork rolls onto your plywood.
If your cork wall is wider than one roll of cork (like ours) so you desire to measure and marking the center betoken so your seam ends up centered on the wall.
RELATED: HOW TO INSTALL SHIPLAP IN four Elementary STEPS
Next, spray a 2′ long section with your adhesive and then use your J-roller to roll the cork out onto the plywood, adhering it carefully along the center line.
The reason you do this in small sections is because yous only accept most lx seconds until the adhesive is ready and at its maximum ability to adhere.
Continue spraying and rolling minor, 2-iii′ sections until the commencement half of the plywood is covered.
Leave any extra cork overhanging the edges for now – you'll trim that upwards later.
Then, exercise the aforementioned thing on the second half, being careful not to go spray adhesive on the cork already installed.
We used a folded upwardly slice of newspaper to protect the installed cork equally nosotros sprayed near the center line.
Equally you're installing the second cork roll, make sure to line up the center line get-go and utilise the J-roller to roll it in identify before setting downwardly and rolling the rest of the cork panel.
And e'er roll information technology towards the center to prevent a gap from forming betwixt the two cork rolls.
STEP 3: Cut away excess cork.
After the cork is adhered to the plywood and you've given information technology an hour or and so to dry out, plough the board over and use a box knife to cut away the excess cork.
STEP 4: Attach your corkboard to the wall.
Lastly, utilize your drill to hang your cork lath on the wall using screws and decorative washers.
We placed screws in every corner, and and then nigh every 2′ around the perimeter.
Chris also placed two into studs in the middle of the board.
If needed, use a stud finder to locate your studs.
Screwing into the stud gives it much more stability.
Finally, hang your artwork or office reminders and you're done!
I just honey how Andrew's turned out!
And he was ECSTATIC over hanging his mementos on that corkboard wall. 🙂
Things to consider when making a cork board for the wall:
How thick does a cork board demand to be?
I don't think it needs to be very thick – specially if you're putting it on plywood!
Ours only ended up being 3/32″ of cork so 1/iv″ of plywood.
But the tacks went into it simply corking!
The best way to evaluate is to make sure you take enough thickness in your corkboard walls to support the depth of your tacks.
How do you hang cork board without nails?
As y'all saw in our tutorial, we hung ours with screws so it would be easily removable in the future!
If y'all're not doing an entire wall and wanted to hang a smaller DIY cork lath, then you could besides use 3M command strips!
Every bit promised, here are the printable instructions:
Active Time: 1 hour
Additional Fourth dimension: 30 minutes
Full Time: 1 hour xxx minutes
Difficulty: Easy
Estimated Cost: $50
Instructions
- Apply your jig saw to cut your plywood practise the verbal dimension of the wall you lot're wanting to cover.
- If your wall is wider than one 24" wide curlicue of cork, then measure and mark the center line on your plywood.
- Spray a 2' section on ane one-half of your plywood and attach the cork roll to the plywood using a J roller to roll it out.
- Continue spraying and adhering 2-3' sections until the offset half is covered.
- Spray and adhere the 2d ringlet of cork using the same method, making certain not to get spray adhesive on the first side's cork and being careful to align the center line offset and foremost all the way down.
- Turn the plywood over and use a box knife to trim off whatsoever backlog cork around the edges.
- Hang your corkboard walls using screws around the edges (in the corners and ever 2' effectually the perimeter) and into two studs in the middle of the wall.
- Hang your artwork or office items on your new cork wall!
So, what do you think?
Fix to tackle a cork lath for the wall in your function or kid's room?
I promise this uncomplicated DIY tutorial for how to brand a cork wall was helpful!
Feel complimentary to ask any questions in the comments.
And be sure to check out all the other amazing $100 Room Claiming projects here:
DON'T FORGET TO FOLLOW Along!
INSTAGRAM | PINTEREST | FACEBOOK
Source: https://joyfulderivatives.com/removable-corkboard-walls/
Posted by: floriobaccomithe.blogspot.com
0 Response to "How To Install A Cork Wall"
Post a Comment